Lotem - Prinergy Evo

[kala]

How to find out which interlock is open? like runnning diagnostic software ???
do u have the pix of magnetic switch.if its the problem means how to rectify it

[PACH]

How to find out which interlock is open? like runnning diagnostic software ???
do u have the pix of magnetic switch.if its the problem means how to rectify it

Take the cassette out and look at the RHSide of the opening where the cassette goes in. You will see a small back block with wires attached to it. On the cassette side you will see the other part which is a block of magnet. When you push the cassette in the magnets have to be close enough to make the circuit.
You can not run diag on the interlocks.
have you got the small RED overide block that you cheat the motor interlocks? If you use this in the front cover with the cassette installed and still get the message Cassette int. open than it is the magnetic inerlock that is not makink.

[kala]

open than it is the magnetic inerlock that is not makink.

couldnot understand ur last point. my point is if magnetic switch is the problem then wht is the solution for it whether we have to change the switch r wht to do, kindly advice iam suspectiong proplem from casette side only.

[kala]

we have the cheater, rightnow iam at home let me try to observe more thing stomorrow in office and let u know thanks

[kala]

Facing problem in Dolev 800 v running in mac g3 = psm 8 + os 10.4 on tsp giving error sometimes 7120 and sometimes 7122. kindly help where is the problem tsp or tsp cable or psm. Is it possible to run Neutral tsp card (62 pin) on mac

regarding those plate problem in lotem time being i have shifted back into brisque again let u know once i get support from kodak regarding this.

Interlock active regarding casette problem also pending for hardware engineer from kodak

[PACH]

Facing problem in Dolev 800 v running in mac g3 = psm 8 + os 10.4 on tsp giving error sometimes 7120 and sometimes 7122. kindly help where is the problem tsp or tsp cable or psm. Is it possible to run Neutral tsp card (62 pin) on mac

regarding those plate problem in lotem time being i have shifted back into brisque again let u know once i get support from kodak regarding this.

Interlock active regarding casette problem also pending for hardware engineer from kodak

Hi Kala,

D800 problem it looks like a hardware problem with your TSP card.

Lotem800- Cassette In Detector. Did you find the magnetic switch that I told you last time? Also, have you got only one cassette for using 11 palte sizes?
The magnet on the RHS of the cassette is easy to remove. It is held in by a cross head screw. You can take it out and put one or two washers at the back to make it come further out from the casstte therefore nearer to the part in the Lotem when you put the casstte in.

[kala]

we have 2 tsp cards sometime its running a day sometimes it running hours sometimes it wont run but error message is always 7120 & 7122 only. is it anyway to test the tsp connection in psm like running the diagnostic in brisque to find that tsp is functioning or not. kindly suggest

[kala]

is it possible to connect a 62 pin both end neutral tsp card in dolev 800v though the tsp_75 model has 62 pin on one side and 22 pin on the other side.

[PACH]

is it possible to connect a 62 pin both end neutral tsp card in dolev 800v though the tsp_75 model has 62 pin on one side and 22 pin on the other side.

Kala,

As you have a Brisque, why don't you try and connect your Dolev to the TSP card in the Brisque and run it when possible.
OR, put your TSP card from the Mac into the Brisque and run the diag on it.
OR, swap your Brisque TSP card with the one in the Mac to see if you still get error messages
DO NOT forget to power down both the Mac and the Brisque.

[kala]

As you have a Brisque, why don't you try and connect your Dolev to the TSP card in the Brisque and run it when possible.
i cannot connect tsp card in the brisque to Dolev becaz the tsp connect with brisque has 62 pin cable on both the end though my dolev has 22 pin in the cpu

OR, put your TSP card from the Mac into the Brisque and run the diag on it.
though brisque is now connected with lotem and here no one is ready to switch even we never switched off the brisque

OR, swap your Brisque TSP card with the one in the Mac to see if you still get error messages
i told u earlier too i tried 2 tsp what i have but anyway once my prinergy problem solved then i will use the tsp which is lying in the brisque.

what abt neutral card tsp is it posssible to connect dolev though the cable has 62 pin on both sides which connect tsp to dolev.