Lotem - Prinergy Evo

[PACH]

As you have a Brisque, why don't you try and connect your Dolev to the TSP card in the Brisque and run it when possible.
i cannot connect tsp card in the brisque to Dolev becaz the tsp connect with brisque has 62 pin cable on both the end though my dolev has 22 pin in the cpu

OR, put your TSP card from the Mac into the Brisque and run the diag on it.
though brisque is now connected with lotem and here no one is ready to switch even we never switched off the brisque

OR, swap your Brisque TSP card with the one in the Mac to see if you still get error messages
i told u earlier too i tried 2 tsp what i have but anyway once my prinergy problem solved then i will use the tsp which is lying in the brisque.

[COLOR=navy]what abt neutral card tsp is it posssible to connect dolev though the cable has 62 pin on both sides which connect tsp to dolev.

[/COLOR]

never tried this so I can recommend it.

[PACH]

[/COLOR]

never tried this so I can NOT recommend it.

never tried this so I can NOT recommend it

[kala]

Is there is anyway to connect psm 8.0 to lotem 800v2 ???

[PACH]

Is there is anyway to connect psm 8.0 to lotem 800v2 ???

Simple answer is NO>

[kala]

Regarding Lotem-prinergy-xpo problem - we tried today by firing a 1bit tiff job instead of pdf thro prinergy evo though the problematic plate size shows images but laser lines came this is fyi. Meanwhile we want to know if u fire pdf or ps from brisque everything is perfect but firing 1bit tiff in brisque also giving lines and screen lose problem. How to avoid it

regards

[PACH]

Regarding Lotem-prinergy-xpo problem - we tried today by firing a 1bit tiff job instead of pdf thro prinergy evo though the problematic plate size shows images but laser lines came this is fyi. Meanwhile we want to know if u fire pdf or ps from brisque everything is perfect but firing 1bit tiff in brisque also giving lines and screen lose problem. How to avoid it

regards

Do you send a 1 Bit TIFF to the Brisque to output?

Do you get any error messages when you get the problem?

[kala]

Do you send a 1 Bit TIFF to the Brisque to output?
i told we never tried 1 bit tiff to brisque though we are facilng laser line and screen lose problem in brisque but if u fire the job ps files thro brisque no problem perfect. though u aware the upgrade into prinergy and facing problem in particular few plates thro refined pdf but same file sent thro 1 bit tiff license it shows image but again the same type of problem like in brisque laser lines on images.

Do you get any error messages when you get the problem?
what error message where and when and which station you want. but i never get any error if i fire it thro brisque or prinergy by 1 bit tiff

[kala]

Hi

Any idea abt the below Lotem error:
Regarding drum deviation error :

we tried to change the distribution board after that also drum deviation error occurs then today we tried to change the drum driver board after that 3 plates got exposed. Next the below error occurs.


Error on load roller value.value HP detector No change/No valid state of detector in off operation.
The task load roller off switch failed.
The task drum power switch off failed.
MCF card startup requires.
Slave sproc prepare access failed.

* that prinergy error was solved by sql tiff method.
the tsp problem was solved by slot and new tsp.

This is FYI

[kala]

after again changed into my drum driver board and reload the registry the software works but my question is if u change the drum driver board is there is any setting to change somewhere or in registry we have to cahnge kindly confirm

[PACH]

after again changed into my drum driver board and reload the registry the software works but my question is if u change the drum driver board is there is any setting to change somewhere or in registry we have to cahnge kindly confirm

Hi Kala,
Is the Lotem working now?
The answer to your question: if you change the Drum PSU ( ELMO) you do not have to change anything in the registry.